Everyone wears out their Park Tool work stand clamp covers at some point. Find replacement covers for yours here. Each cover is constructed of soft, durable composite rubber. See below to determine which covers fit your Park Tool stand clamp: - 1002: fits 100-3X and 100-5X extreme range clamps - 1185: fits clamps on the repair stands PCS-9, PCS-10, PCS-11, and PCS-12 - 1259: fits 100-4X, 100-6X, 100-7X, and 100-15X clamps - 1960: fits 100-3D, 100-5D, and 100-25D Professional Micro Adjust Repair Stand Clamps - 468B: fits clamps with double cable reliefs, including 100-3C, 100-5C, 100-8C, 100-8Y, and 100-9C clamps - 467B: fits clamps with single cable relief, including PRS-2 through PRS-8 (for older-style clamps, non-current) - 468G: fits PCS-1 and PCS-2 clamps with double cable reliefs (clamp models: 100-1C, 100-1CA, and 100-2C) - 467G: fits PCS-1 and PCS-2 clamps with single cable relief (for older PCS-series stands only; not for current model stands) - 466: Rubber Replacement Clamp Cover Set (fits older clamps with plastic-dipped jaws)
Park's Paper-Towel Holder is an accessory for Park's Professional Race Stand (sold separately). It attaches easily and holds a standard roll of paper towels. It also works great for hanging clothes, wheels and tires.
The RPP-1 offers simple but effective protection for your service area. This 32" tall pad prevents damage to bikes caused by being leaned against or knocked over onto your Park Tool professional repair stand. Covered with an attractive Park Tool blue vinyl finish for easy wiping off of dirt and grease. - Compatible with Park Tool Shop Repair Stands with a 2" diameter lower post, including all generations of PRS-2 and PRS-3 - Easily removed and installed with hook-and-loop material
The Travel and Storage Bag is a heavyweight nylon bag with a shoulder strap. This bag is designed for transporting and storing your Park Professional Race Stand. It makes travel easy and convenient, while also protecting your stand.
Keep your most-needed bike repair tools and supplies close at hand with Park's Work Tray. It easily installs on your Park PRS-15, PRS-10, or PRS-11 Repair Stand (sold separately). And it features 2 separate compartments, a lube holder, a tool/towel bar, a tab system that holds plastic grocery bags and 2 receiver pods for extra accessories.
For wheels to perform properly, it's important that the rims be centered over the hubs. To check this, and to make precision adjustments, Park's Wheel Alignment Gauge (also called a dishing tool) is a must. It allows you to easily check centering on road, mountain and BMX wheels from 16 to 29 inches in diameter. It works with any hub width and its innovative design even allows it to be accurately used with the tire still on the wheel. The Wheel Alignment Gauge is a necessity for every wheelbuilder.
Park's Truing Stand Upright Extensions are made of durable chrome-plated steel and have quick-releases so they install in seconds to your Park TS-2 Professional Truing Stand (sold separately). The Uprights allow the stand to be used with wheels with hubs up to 160mm wide (found on some tandems and downhill bikes), and 29-inch mountain-bike wheels. Plus, there are specially sized bosses that act as adapters to hold wheels with 20mm through-axle hubs, too.
Park's Cast Aluminum Tool Tray attaches easily to most of Park's repair stands (sold separately) to keep your tools, lubes and small parts close at hand. It has deep sides so your small items stay put, a holder for cans of lube and slots for holding your tools. This handy tool fits Park's PRS-2, PRS-3, PRS-6, PRS-13, PCS-1, PCS-1 and PCS-4 repair stands manufactured after June 1996 (stands sold separately).
Park's Bench Mount Home Mechanic Repair Stand features a quick adjusting cam-type clamp that fits on frame tubes up to 76mm in diameter. Plus, the clamp rotates 360 degrees for access to any part of the bike for easy repairs. The clamping pressure is fully adjustable, too, to prevent damage to lightweight frame tubes. Plus, this excellent stand boasts a durable powdercoat finish, protective rubber jaws, and it mounts to any flat surface (bolts sold separately), so you can turn just about any nook and cranny in your house or garage into a proper bike repair facility!
Park's Home Mechanic Wheel Truing Stand allows extremely accurate and reliable wheel truing and even building at an economical price. It's constructed from heavy-gauge steel and works with most wheel sizes and hub widths. It can be bolted to a bench for additional stability.
Perfect for taking to races and rides, the Portable Workbench is a bench that folds for easy transport and storage. It features a large work surface with specially sized slots, holes, and recesses and for holding tools, shop towels, lubes, beverages, etc. The folding steel legs provide a solid base for a toolbox and supplies, too.
The PCS-9.2 is a basic workstand designed and built for the home mechanic. A stable way to hold nearly any bicycle for adjustments, cleaning and repair. The stand folds for transport and storage and is adjustable in height to always keep your work at a comfortable level. Able to hold up to 80 pounds (36kg), the PCS-9.2 is the perfect way to upgrade your home shop. - Fully adjustable clamp to fit 1- to 3-inches (25mm–76mm) diameter tubes and seat posts of any shape and material - All steel structure for maximum stiffness and durability - Teardrop shaped tubing adds strength and ensures perfect positioning during use and folding - Folds quickly, easily and compactly for storage utilizing ergonomic knobs and smooth operating support straps - Height adjustable from 39- to 57-inches (99cm–145cm) - Durable textured powder coat finish - Super strong glass filled nylon composite fittings and top tube internals creating smooth rotation and secure positioning
Park's adjustable linkage shop clamp is found in more shops than any other professional level clamp. The 100-5C features solid cast aluminum construction and durable replaceable clamp covers. Clamp has reliefs on both jaws for cable routing, and feature replaceable jaw covers. - Fits PCS-4, PRS-5, PRS-6, and PRS-7 stands made after 6/96 - Fits bike frame tubes from 1" to 1 5/8" (25mm to 41mm) - The clamp jaws are nominally 4 inches (10cm) wide - Uses 468B jaw covers
The Team Race Stand is a Euro-style stand that securely holds your bike without clamping the frame tubes or seatpost but by holding it by either the front or rear dropouts via quick releases. It's ideal for bikes with ultra-light frame tubes and seatposts, and for bikes with tight access areas that can't be clamped. For easy wrenching this stand rotates horizontally 360 degrees and can be adjusted up and down from 28 to 38 inches (bottom bracket to the ground). This great stand was originally designed for the mechanics of the pro peloton, and is now available to home mechanics everywhere. Plus, the stand folds down to 33-inches long, so you can easily throw it in the back of your car.
A workstand is the backbone of any shop. Holding the bike at a convenient working height allows easy access for adjustments, cleaning and repair. The PCS-10.2 Deluxe Home Mechanic Repair Stand was designed and built using our 50 years of experience creating professional shop stands used in shops around the world. The unique three-point leg system and stout adjustable uprights create an extremely solid platform capable of handling bikes up to 80 lbs. (36kg). Easy to set up and use in a home shop, the PCS-10.2 also folds easily for transport or storage. - World famous Park Tool cam actuated, micro adjustable clamp that allows quick entry and exit and fits 1- to 3-inches (25mm–76mm) diameter tubes and seat posts of any shape and material - All steel structure for maximum stiffness and durability - Teardrop shaped tubing adds strength and ensures perfect positioning during use and folding - Folds quickly, easily and compactly for storage using aluminum quick release mechanisms and strong tubular support braces - Quick release height adjustment from 39- to 57-inches (99cm–145cm) - Durable textured powder coat finish - Super strong glass filled nylon composite fittings and top tube internals creating smooth rotation and secure positioning - Includes height adjustable compact tray to hold small parts, a few tools and the PTH-1 Paper Towel Holder (optional accessory)
Traveling mechanics choose the Super-Lite Team Race Stand because this Euro-style stand securely holds bikes without clamping the frame tubes or seatpost but by gripping the front or rear dropouts via quick releases. This is ideal for bikes with ultra-light frame tubes and seatposts, and for bikes with tight access areas that can't be clamped. For easy wrenching, this stand rotates horizontally 360 degrees and can be adjusted up and down from 28 to 38 inches (bottom bracket to the ground). Plus, the gossamer 13.5-pound weight makes it the ideal choice for traveling mechanics everywhere.
The PRS-4.2 is a professional quality bench mount repair stand designed and built to withstand the rigors of everyday shop use. Includes three mounting holes, making it possible to clamp as high as 16.25" (41cm) from the bench surface. - Shop quality 100-3C Clamp quickly adjusts to fit any frame tube up to 1-5/8" (41mm) - The clamp jaws are nominally 4 inches (10cm) wide - Clamping height can be raised from 6.5" to 16.25" (92cm to 41cm) above the bench surface - Clamp rotates 360 degrees - Heavy gauge steel tubing - Chrome plated for durability
Park's TS-2.2 Professional Truing Stand has been a staple in bike shops for decades because it's so reliable and easy to use. It accepts all common wheel diameters up to 29 inches with and without tires. It’s made of heavy chrome-plated steel with nylon bushings at pivot points and can be bench-mounted, vise-held or attached to Park's Tilting Base (sold separately). The best feature is that this stand automatically centers rims over the hubs, which saves time repairing and building wheels. Also, installing the wheel and positioning the caliper for truing is quick and easy thanks to the stand's separate knobs for each setting. This is an awesome truing stand that will last a lifetime.
Park Tool's Deluxe Home Mechanic Repair Stand is a heavy-duty folding stand with your choice of shop quality clamps. Perfect for heavier duty home use or portable shop use, the PCS-4 features a rock-solid, four-point leg system that folds together for storage, steel powder-coated tubing, and a composite horizontal tube. • PCS-4-1 uses the 100-5C Adjustable Linkage Clamp. • Clamp rotates 360º and is adjustable in height up to 67” (170cm) • Adjusts quickly from 55" to 72" • Approximate weight 26 lbs (11.8 kg) NOTE: The maximum weight holding capacity of the PCS-4 is 45 kg (100 lb.). However, this assumes the weight is centered over the legs.
Page 1 of 1