Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands
  • Show More Model Years
  • Show Fewer Model Years

Stems

$1,006.00
Send a shiver down the spine of your competition with Zipp’s integrated Vuka Stealth. This ultra-stiff, fully carbon cockpit is even faster than it looks. With almost 2,000 fit options, dialing in your perfect position is finally possible, allowing you to get more aero, produce more power, and conserve more energy. Choose from three stem lengths, each of which includes spacers to increase stem length by an additional 10mm. You can make additional adjustments to the stack, reach, and pad width and position, as well as extension width and length (extensions are sold separately). The base bar's truncated airfoil reduces drag and meets all UCI regulations, while the grips are roughened so you don't need tape. Zipp's Rapid Routing makes running the cables inside the bars easy so everything is tight, orderly, and above all—fast.
$179.95
You really can have it all-the new WCS C220 stem rivals the performance of the revolutionary C260 stem design, but it's quicker and easier to install and remove, thanks to a press-fit handlebar clamp interface and forward-facing hardware. First proven on the Ritchey TRAIL stem, the C220 handlebar clamp design creates a more secure interface by wrapping a full 220-degrees over the handlebar. Bolt forces are aligned with the clamp so that the stem body 'embraces' the handlebar, which is less prone to damaging lightweight bars. This clamp design allows for a lighter faceplate and stem body with no sacrifice in strength or stiffness. The Carbon Matrix stem body is forged 7075 aluminum with a stiffness-enhancing carbon exoskeleton which makes this 12% stiffer than the WCS alloy C220 stem. Premium quality CRMO steel bolts are used throughout. - Material: 3D forged 7075, carbon encased body - 4 x 4mm coated CrMo steel forward-facing faceplate bolts - 2 x 4mm coated CrMo steel offset steer tube clamp bolts - 5Nm torque max on all hardware - Compatible with all 31.8mm bars - Press-fit clamp design installs and removes like a standard stem - Angle: 84/6 degree - Stack: 42mm - Steerer: 1-1/8" - Faceplate Width: 42mm - Matte UD carbon finish - 126g (110mm)
$150.00
Waste not, want KNØT. Part of the KNØT SystemBar, this aluminum stem helps save six watts over a traditional round handlebar. Not only that, you can adjust the bar position. Have cake. Eat cake. Where it thrives: The open road, up and down hills What it's built for: Aerodynamics, control Highlights: - One-piece looks, two-piece function - Wind tunnel proven, hides cables - Compatible with 2019+SuperSix EVO
$150.00
System = speed. Paired with the SAVE or KNØT SystemBar, you end up with the speed and good looks of a one-piece system with the adjustability of a two-piece. Where it thrives: The open road, up and down hills What it's built for: Aerodynamics, efficiency Highlights: - Integrated computer mount - Compatible with most bicycles - One-piece looks, Two-piece function
$109.95 - $140.45
- CNC machined 2014 aluminum body and 7075 aluminum clamps - 240 degree wrap-around, twin plate clamping system - External webbing to maximize structural strength - 118-158g including stainless steel bolts
$125.00
The Alpinist Stem is a light and stiff alloy stem. Designed to perform during big attacks in the hills and furious bunch sprints, while weighing just 110g for featherweight performance when the road goes up. With classic lines, traditional clamp, and huge range of lengths and rise angles, this stem earns the Alpinist name as the ideal upgrade to almost any bike. LIGHT: Every Alpinist product puts a premium on lightweight, because we know lightweight is a key ingredient to creating magical ride quality. Using premium 7075 Alloy and Ti hardware, the Alpinist stem weighs a feathery 110grams in a 110mm length. STIFF: 3D Forged and CNC machined, despite its feathery weight the Alpinist stem delivers the stiffness needed for big power and precise, sharp handling in the most challenging situations. FIT: With seven lengths to choose from, and three different angles of rise, you know you'll find your perfect fit with the Alpinist Stem. Its classic lines, polished black finish, and traditional 31.8mm clamp make it an aesthetic fit with almost any bike. - Material: 3D-forged and CNC-machined, 7075 aluminum - Bolts: Titanium - Lengths: 70, 80, 90, 100, 110, 120, 130mm - Rise: 6, 12, or 17-degree rise - Weight: 110-115g (for 110mm) - Clamp Diameter: 31.8mm - Clamp Height: 40mm - Steerer Tube: 1-1/8"
$125.00
The Control Stem is tailor-made with a 35mm clamp to partner with the Control SL bar, delivering more stiffness and more control—coming in at an incredibly light 100g (50mm). Turns out, you can have it all. LIGHT: Where light weight and stiffness meet. Its high-quality 7075 Alloy and Ti hardware and featherweight function make the Control SL Stem a perfect match for race-day setups. STIFF: Made with the same integrity as the suite of stiff Roval components, the Control SL provides race-ready rigidity allowing for precision on the bike. FIT: With six lengths to choose from and 6 degrees of rise, you know you'll find your perfect fit. - Material: 3D-forged and CNC-machined, 7075 aluminum - Bolts: Titanium - Length: 50mm, 60mm, 70mm, 80mm, 90mm, 100mm - Rise: 6 degree rise - Weight: 100g (at 50mm), 130g (at 100mm) - Clamp Diameter: 35mm - Clamp Height: 40mm - Steerer Tube: 1-1/8"
$125.00
Making its debut on the all-new Roubaix the S-Works Future stem is the stiff lightweight upgrade that your Roubaix has been waiting for. It's compatible with all Future Shocks and our Specialized accessory mount and its sleek design will create a seamless integration. - Sleek & seamless integration with all Future Shocks. - Supremely stiff for responsive handling and feel. - Compatible with the Specialized accesory mount. - 6-degree rise - Length options: 70-140mm - Approximate weight: 145g (100mm)
$124.99 - $125.00 $125.00 On Sale
Lean and clean. The lightweight and stiff S-Works Tarmac Stem features integrated cable routing for Tarmac SL7 models to clean up the cockpit without complicating the bike build. - Compatible with Tarmac integrated cockpit. - Integrated face-plate computer mount. - 80-140mm length options. - 6 and 12 degree rise options. - Approx. weight: 155g (100mm)
$94.99 - $104.99
Inspired by the sleek and deadly lines of a Copperhead snake, the sweeping center channels of the Copperhead stem wrap around the entire stem to minimize material while delivering the a stong steerer mounted stem. DEITY's focus on durability and dedication to the symmetry between strength and weight is showcased in the balance of style and function that is the Copperhead stem. - Designed for all applications from All MTN to Slopestyle and anything in between - CNC Machined from a solid block of 6061 T6 Aluminum - Exceptionally detailed chamfered edges and channels throughout - 55mm wide clamping platform
$79.99
Hollow stems are cold forged from the highest quality 6061-T6 aluminum available. Featuring an open skeletal design and a dual mid-bolt wedge mounting system, they are lightweight yet maintain a very high level of strength. A 53mm extension stem weighs just 218 grams/7.7 ounces. By removing the rear pinch bolts and moving the mounting bolts to the middle of the stem, we reduced the weight and size and eliminated a serious hazard to the rider’s knees. These stems come with either a 48- or 53mm extension and a 22.2mm bar bore. To ensure proper clamping force, the stem must be mounted on a fork with at least 45mm of exposed steerer tube. Not compatible with forks that have carbon fiber steerer tubes.
$79.99 $125.00 36% Off
Specialized's S-Works SL Stem is sleek and lightweight. - 3D-forged and CNC-machined, 7075 aluminum road stem . - Includes expander plug for carbon steerer tubes and titanium hardware.
$79.95 $150.00 47% Off
The S-Works Venge stem has been designed to work as a system with the Venge cockpit to optimize aerodynamics, stiffness, and weight. - Seamless integration with the 2019 Venge frame and hidden cables - Optimized for use with the S-Works Aerofly II handlebars for integration - Its dropped clamp and flat upper profile cheat the wind for the maximum aero advantage - Extremely stiff for responsive handling and out of the saddle sprinting
$70.00
Mix and Match might work for clothing, but not your mountain bike cockpit. The new Descendant stem is 3D forged from 7075 alloy, then machined for weight reduction, and is the perfect match for your Descendant bars—not that you’re worried about that kind of thing. Built strong, to take on the world’s toughest trails, Descendant stems keep you pointed in the right direction. - Colors: Black - Material: Al-7075 - Lengths: 40mm, 50mm, 60mm - Bolts: Steel - CNC machined for weight reduction - Four bolt handlebar clamp - Two bolt steerer clamp
$69.99
All Box stems are engineered and crafted using our Oversized Technology. As we follow the load paths down the handlebars we have focused our attention on the stem-to-bar interface. Since the Oversized handlebars have an increased wall thickness and tube diameter in this sector we have reciprocated with an augmented stem interface with greater surface area. We’ve done this by moving material from low stress areas. This has greatly minimized twist and contributed to responsiveness. As the stem in mated with the handlebars we have contributed to increased pedaling stiffness by providing a backstop to the “lifting” phenomenon. There is no point pushing hard on your pedals if you can’t pull up on your handlebars and deliver that power. Power can easily be lost to handlebar-to-stem deflection and the consequences can be poor power delivery and steering control. When combined with Box’s other Oversized components, you’ll experience heightened responsiveness and reduced latency. Key differences: This particular model stem pushes our Oversized Technology to the extreme as it maximizes the shift of material from low stress zones to the Oversized interface. These stems are engineered for the smaller-sized racers. -Lightweight 3D Hollow Design -Front-Load Clamp Design to Fight Pull-Up Forces -Large Bar Bore -Large Hollow Clamping Bolts -Superior Strength
$69.99
All Box stems are engineered and crafted using our Oversized Technology. As we follow the load paths down the handlebars we have focused our attention on the stem-to-bar interface. Since the Oversized handlebars have an increased wall thickness and tube diameter in this sector we have reciprocated with an augmented stem interface with greater surface area. We’ve done this by moving material from low stress areas. This has greatly minimized twist and contributed to responsiveness. As the stem in mated with the handlebars we have contributed to increased pedaling stiffness by providing a backstop to the “lifting” phenomenon. There is no point pushing hard on your pedals if you can’t pull up on your handlebars and deliver that power. Power can easily be lost to handlebar-to-stem deflection and the consequences can be poor power delivery and steering control. When combined with Box’s other Oversized components, you’ll experience heightened responsiveness and reduced latency. Key differences: In this particular model stem we’ve modulated the Oversized formula to emphasize pedaling stiffness. We have transferred material specifically to sectors that experience sudden stress from pulling up on the handlebars. You’ll feel a difference in your acceleration. These stems are engineered for the larger-sized racers. -Material: 6061-T6 Aluminum -Process: Cold-Forged -Hardware: Chromoly Clamping Bolts -Finish: Anodized w/Laser-Etched Graphics Weight: -48mm: 280 g / 9.8 oz -53mm: 290 g / 10.2 oz
$69.99
All Box stems are engineered and crafted using our Oversized Technology. As we follow the load paths down the handlebars we have focused our attention on the stem-to-bar interface. Since the Oversized handlebars have an increased wall thickness and tube diameter in this sector we have reciprocated with an augmented stem interface with greater surface area. We’ve done this by moving material from low stress areas. This has greatly minimized twist and contributed to responsiveness. As the stem in mated with the handlebars we have contributed to increased pedaling stiffness by providing a backstop to the “lifting” phenomenon. There is no point pushing hard on your pedals if you can’t pull up on your handlebars and deliver that power. Power can easily be lost to handlebar-to-stem deflection and the consequences can be poor power delivery and steering control. When combined with Box’s other Oversized components, you’ll experience heightened responsiveness and reduced latency. Key differences: In this particular model stem we’ve tailored the Oversized strategy to favor utility and access. The geometry has been altered to allow for easy handlebar removal while at the same time scavenging material from low stress zones. Ideal for those who don’t want to compromise on user experience to gain performance. These stems are engineered for the larger-sized racers.
$69.99
The pro from down under, Boyd Hilder, is also getting a signature stem in our lineup, and it's well deserved. Boyd likes the familiar design DNA of our stems, but had specific Specs in mind to suit his all-around riding style. Clean looks, comfortable reach/rise, and a palm tree etching so you can take the beach-y vibes with you. - Boyd Hilder Signature - Unique surface contouring for superior handlebar grip - Six bolt clamping configuration - 6061-T6 aluminum, CNC machined
$69.99
Tom Dugan's signature DGN v2 stem is a classic top-load, 6-bolt design. Along with other Odyssey v2 stems, the bolt heads have been upgraded to a larger size and the clamping area features unique surface contouring for superior handlebar grip - Six bolt clamping configuration - Headset pre-load bolt recess (32mm diameter)
$59.99 - $69.99
- Strong yet competitively lightweight alloy single crown stem for all disciplines - Unique style, modern geometry, and rock-solid construction, without the heavy price tag - Dial your fit with micro-increment size options, tuned to fit any rider size and style - Cockpit setup index lasered onto stem helps with tuning of upsweep and backsweep - Ultra-short stack height and true zero-degree rise - Chamfered bar clamp to reduce stress risers and increase fatigue life in handlebars
$59.99 - $69.99
- Strong yet competitively lightweight alloy single crown stem for all disciplines - Unique style, modern geometry, and rock-solid construction, without the heavy price tag - Dial your fit with micro-increment size options, tuned to fit any rider size and style - Cockpit setup index lasered onto stem helps with tuning of upsweep and backsweep - Ultra-short stack height and true zero-degree rise - Chamfered bar clamp to reduce stress risers and increase fatigue life in handlebars - Recommended for: ASTM 5, All mountain, enduro, trail, free ride, DJ, E-Bike
$64.00 - $66.00
Whether you’re trying to hold your line on a jackhammer descent or stick a landing on a 20-foot gap jump, you need confidence and control. The heart of the beefy HOLZFELLER Stem is its 6066 aluminum body, 3D forged into a thing of beauty with all-new graphics. It takes design cues from the lighter AKA Stem, but has added strength for the most extreme DH and Freeride situations. The HOLZFELLER features a 2-bolt steerer clamp and 4-bolt handlebar clamp and weighs less than 200g (190g for a 40mm length). It’s available in two color choices and three lengths: 40mm, 55mm or 60mm. HOLZFELLER Stem is also available with a larger 1.5-inch steerer tube diameter.
$64.99
The Chester 35 Direct Mount stem is a practical 2-piece design with big bold graphics and that legendary bomb-proof Race Face toughness baked right in. - The Chester 35 direct mount stem is an all new 2 piece direct mount design - Forged and machined from 6061 aluminum - Weight saving single bolt faceplate - Four bolt bar clamp holds bar securely in position. - Interlocking U-Shaped Handlebar Clamp Geometry transferring more load through the stem body and not the bolts - Faceplate eliminates 'stress risers' which can cause your bar to bend or break
$60.00
3D-forged and CNC-machined from 6061 aluminum the Future Stem Comp is optimized for use with all Future Shocks. It's also compatible with our Specialized accessory mount for seamless integration. - 3D-forged and CNC-machined, 6061 aluminum, Future Shock-optimized stem. - Available in 6-degree angles and 60, 70, 80, 90, 100, 110, and 120mm lengths. - Compatible with the Specialized accessory mount.
$60.00
On today's road bikes, silver stands out amid the sea of stealthy black color schemes. This time-honored color is available on the Zipp Service Course stem. Since the introduction of our line of Service Course and Service Course SL components, we've had amazing success with our pro-level athletes in all disciplines. While the successes have reinforced our design decisions, we have also drawn from their feedback. We not only learned how and why athletes make their equipment choices, but how our manufacturing methods and materials affect product performance. With new knowledge as well as new engineering methods, we are proud to introduce our completely redesigned line of Service Course and Service Course SL stems. - Class-leading stiffness-to-weight ratio - More options for a better fit - New faceplate and geometry for greater stiffness and easier installation - Distinctive silver finish
$59.99 $60.00 On Sale
The new Trail stem is forged and CNC-machined to meet the demands of today's trail riding with a sublime stiffness-to-weight ratio. - 3D-forged and CNC-machined 6061 alloy construction - 4-bolt oversized 31.8mm handlebar interface with relieved faceplate - Compatible with carbon composite handlebars
$59.90
- Solution for riders wanting to raise their drop bars for added comfort - 225mm tall quill (210mm above the min insertion line) - Forged aluminum - 22.2mm quill - 25.4mm clamp - 386-415g
$55.00
Descend with confidence. The perfect match for any trail or enduro bike paired with the HollowGram SAVE Riser 35mm handlebar for increased descending prowess. Where it thrives: Challenging trails, down hills What it's built for: Control, confidence Highlights: - 35mm clamp size - 37mm length - 0° degrees rise
$50.00 - $55.00
The workhorse. Whether you're upgrading your stock parts or looking for something a bit more eye catching, the alloy ONE stem delivers. Where it thrives: The open road, gravel roads, up and down hills What it's built for: Agility, control Highlights: - Lightweight aluminum construction - Wide range of sizes - Eye-catching and sleek design
$54.99
The Box Two Front Load is a modern, 22.2 stem designed specifically for BMX racing. Box Two Front Load stem bodies are cold-forged and CNC-machined from the highest quality 6061-T6 aluminum. The lightweight front clamps are cold-forged and CNC-machined for increased stiffness and strength. -Material: 6061-T6 Aluminum -Process: Cold-Forged -Hardware: Chromoly Clamping Bolts -Finish: Anodized w/Laser-Etched Graphics Weight: · 48mm: 224 g / 7.9 oz · 53mm: 230 g / 8.1 oz
Page 1 of 2 Next page